REQUIREMENTS FOR OPERATION:
- DTneo or DTneo+ Ballast (V-Mount DC use only)
- DPOWN, DPOWN-3 or DPOWN-10 Series Light Head Cable
- FOR AC USE - Add DLPS15-100 Adapter
DLED4N-BI - Bi-color 2700K - 6600K LED Light Head
The Dedolight NEO DLED4N-BI light head beautifully blends bi-color output in the popular "M" size dedolight light head size. The "M" size light head is in the same scale as a classic 150w DLH4 unit, making it the most popular LED size dedolight to build kits from. Three of these light heads, along with three DTneo ballasts, can fit into a medium sized rolling hard case. Like its predecessor, the DLED4-BI, this light draws a constant 40W of power from the DTneo ballast by alternating between sets of 40w tungsten LEDs and 40w daylight LED's mixed in the COB. This means the light delivers full 40W output at all times, from 2700k to 6600k, rather than splitting power between colors. Unlike previous models of the DLED4, the NEO version has deeper color integrity in lower dimming ranges and in dimming. While the DLED4 also shares a body style with the DLED7N unit, it does so with a smaller COB and therefor has an all-around larger output and scale through the front lens. The size of the COB in comparison to the lens delivers beam optimization to the highest level in the M-size Neo LED models. Its output ratios are higher, more perfect in balance, strength and control. The DLED4N unit boasts a massive 60° - 4° focusing range (1:12 light ratio) that sets it aside from the rest of the pack, including everything else in the focusing LED market (which is already very small).
Unlike open-faced LED lights that require beam-shaping accessories to get a fixed beam angle, Dedolight LED focusing lights provide a manual focusing range of 60° - 4° (1:12 ratio) straight out of the box. The DLED4N-BI light head also features some new housing updates: it is shorter front to back as the chassis connector is relocated to the bottom. The back casing redesign cuts down light leaks even further as well.
Difference Between DLED4N and DLED7N
Both the DLED4N and DLED7N light heads share the same housing and operate with DTneo or DTneo+ ballasts, using the same accessories. The differences lie in the power output versus beam optimization: the DLED4N is a 40W light head, while the DLED7N is 80W. With more diodes in the COB the DLED7N generates more output and heat making it an actively cooled light. While nearly silent, the larger COB results in more punch and a shorter focusing range of 60° - 6° (1:8 light ration). On the other hand, with a smaller COB, the DLED4N is passively cooled offering more optimization on the beam focusing range, quality and considerably longer use in a DC setup. Due to its beam quality the DLED4N unit also has broader light ratios when using optical accessories like the DPBA-714 unit.
DTneo Ballast
The DTneo series simplifies control compared to the previous DT4 series. The DTneo and DTneo+ ballasts offer AC/DC operation, a V-mount plate for battery use, and DMX as a standard feature. The optional AC adapter electronics are housed in a snap-on V-mount battery shell.
The beauty in the DTneo is its auto-detection of which Neo light head model its connected to. If connected to a mono or bi-color light, if identifies the necessary controls and presents them to the user. Use the push/turn knob and OLED display to select between linear or exponential dimming curves, or change color seamlessly without drifting—even at very low dimming levels (0.1 to 100% dimming range). Choose between 8-bit linear or 16-bit advanced control via DMX/RDM protocol, and shoot up to 50,000 fps flicker-free using the high-speed setting. The DTneo ballast is future-proof, with user-upgradable software via USB, and can drive all Neo light heads from 20W to 90W, offering versatile control across the product line.
The DTneo+ ballast supports wireless control via CRMX LumenRadio and Bluetooth.
[TABS]
KEY FEATURES
Color Temperature |
Continuous adjustment from 2700K to 6600K |
Power |
Max power consumption: 40W, alternating between two 40W diode sources (2x 40W) |
Focus Control |
60°-4° (1:12 ratio) with double helix focusing control (3/4 turns). With optional DLWARS lens: 54°-84° (1:21 ratio) |
Cooling |
Passive silent cooling |
Mounting |
Dual 5/8" (16mm) vertical/horizontal receptacles or 1-1/8" (28mm) stud |
Operating Position |
Any position |
Accessory Holder |
"M" size accessories - 3" (76mm) |
Tilt Control |
Permanent friction |
Safety |
Protection Class III, SLEV, IP20 |
Size |
W - 4.3" x L (flood) 6.38" L (Spot) 7.91" x H 7.2" (with extended yoke) |
Weight |
2.9 lbs |
UV |
No UV radiation |
PHOTOMETRICS
Photometrics of the DLED4N-BI are identical to the DLED4-BI light head.
CRI Ra |
97 |
CRI Re |
96 |
CCT |
3112K |
TLCI |
97 |
BALLAST
Dimming |
Linear or exponential curve settings; dimming from 0.1% to 100% |
Max Power |
83 W |
Power Supply |
14.8V battery or snap-on AC/DC V-Mount adapter (DLPS15-100) |
Input Voltage |
15V DC (12-18V) |
Color Control |
Continuous, smooth control - Auto detection adjusts to connected Neo light head model for mono or bi-color control settings as needed |
Display |
OLED screen |
Size |
6.87" x 3.62" x 2.5" |
Weight |
1.25 lbs |
DMX |
XLR5 (DMX512-A) 8/16 Bit |
Wireless |
DTneo+ model only: Bluetooth mesh / CRMX / RDM |
KEY FEATURES
- DMX on all DTneo ballasts
- Smooth dimming, with 16-bit control via DMX/RDM
- Wireless control (DTneo+ model) via Bluetooth and CRMX LumenRadio
- Auto-sensing for different light heads
- Supports DC battery or AC operation
- Flicker-free operation up to 50,000 fps
- OLED display with an intuitive menu
- Future-proof with firmware upgradeability
Suggested Accessories
- DPOWN-3: 9' ballast-to-head extension cable
- DPOWN-10: 33' ballast-to-head extension cable
ACCESSORIES
- DP1.2: Imager projector with 85mm lens (updated version of DP1.1)
- DP2.2: Shutter projector with 85mm lens (updated version of DP2.1)
- DPBA-714: Parallel Beam Intensifier (up to 250% increase in spot intensity)
- DLWARS: Wide-angle lens adapter with rotating barn doors (shifts beam range from 54° to 84°)
Search for all "M" Size accessories for use with the DLED4N!
[/TABS]